Questions & Answers - Questions récentes tagguées wont

Do I need INT-SL+ with 2008 Lexus IS250 or do I need Key-overide-All?

Thu, 02 Jan 2025 15:59:20 +0000

I have installed a EVO-ALL in my 2008 Lexus IS250, I got a INT-SL+ and followed those install instructions. I can't get the INT-SL to recognize the door lock from the door button. After further research, it looks like that module is only for domestic vehicles. It looks like I need the KEY-OVERIDE-ALL for imports. Can someone confirm? I found a specific install for the KEY-OVERIDE_ALL for the lexus, however its completely different than the guide than the EVO-ALL is showing.

I have also been unable to make the remote start work with the EVO-ALL. I got the RFK-411, data link connected it to the EVO-ALL, programmed the keys but nothing as far as remote start works. I

decipher qas completed and vech still wont statr

Fri, 19 Nov 2021 15:18:50 +0000

ceicpher was completed amd passed reinstalled evo and prceeded to finsh set up step 4 test the system perform lock Unlock lock did not see the blue light com on alternates yellow /red lights what am I doing warong some help needed

Any Idea, why EVO-ALL won't start Toyota Sienna 2020 Push-To-Start?

Sun, 22 Nov 2020 19:30:25 +0000

Evo-All does Lock/Unlock, but dosen't start the engine. When press lock three times, the module's Red LED comes on soild and then blue LED;locks vehicle, but doesn't crank (the engine does't start).

2015 Malibu will not shut down after remote start

Tue, 28 Jan 2020 08:26:10 +0000

2015 Malibu flip key. Evo all gmt1 installed. Vehicle starts correctly with 3x lock. Then will not shut down and will shift and drive without key in the ignition. It will then run indefinitely. Does not shut down after the 15 minute run time. Can not stop the engine from running unless I actually unplug the evo module from the vehicle. While running the red light is on on the evo and does not respond to the key being inserted into the ignition, the brake pedal or the fob. Brake lights function correctly on the car.

sn: 001A07 065502

2013 Tacoma Evo one lights won't turn off after time out until doors are opened

Thu, 14 Nov 2019 07:07:25 +0000

Everything work except when remote starter times out the lights stay on and wind go off unless the door is opened

2019 HR-V remote starts, but OEM remote won't unlock evo-one

Thu, 07 Nov 2019 11:54:26 +0000

Okay, after reprogramming the unit a third time, remote start works properly, but the oem remote will not unlock the vehicle. When I use the key to unlock the door, the car shuts down, is this because I am using the kley to open the door? Setting is on disable for kill engine when door opens. Any help? Evo-one with Honda T harness

2015 ACCORD PUSH TO START WONT START

Tue, 08 Jan 2019 13:15:14 +0000

I am asking this question again as the last answer simply asked for my number and I provided it and received nofurther assistance.

I have made it successfully through all stages of installment. I repeat successfully through all stages of installment. The blue light flashes rapidly after the test to confirm my Can/Data/Immo connections are good. Also my hood is not open. Thanks for your assistance. This seems like a great product it just should have a troubleshooting guide for problems and how to fix them without going back and forth over the internet for days at a time. Thanks for all your help guys.001a06 886522

2015 accord push to start wont start

Mon, 07 Jan 2019 12:46:58 +0000

have gone through programming and all seems fine. went through the decryptor thing. put the evo all back on the car. push 3 times to start and blue light flashes and then red light comes on solid for a few seconds then yellow light blinks twice and process is over. Help

LINKR-LT2 (VS-4LU) 4G won't work with EVO ONE

Sun, 16 Dec 2018 18:56:48 +0000

I just got a Linkr-LT2. It came with the Linkr-LT1 quick install guide. I followed the steps in the quick install guide but the unit does not work.
The Linkr LT app only shows my car battery voltage and connection signal. The GPS tracking is working fine. The START/STOP/LOCK/UNLOCK
don't work. I searched the internet and found the "mycar installation guide". I followed the steps to learn the Linkr-lt2 to the Evo one. I turned on the "Fortin 2" function on the EVE ONe. I pressed and held the valet button for 5 seconds but the RED led light on the Evo One did not turn on.

Problem SOLVED. .Linkr LT2 is working fine now...

I found the video on youtube 12voltsolution. The guy pressed the UNLOCK button on car key several times to neutralize the EVO ONE before he did the following steps.

STEP 6. LEARN THE MYCAR TELEMATICS DEVICE TO THE EVO-ONE
In order to communicate with the remote starter, the telematic system must be learned to the EVO-ONE.
1 - Cycle the ignition to the ON position.
2 - The YELLOW LED on top of the EVO-ONE should come ON.
3 - Press & Hold the EVO-ONE programming Valet button for 5 seconds.
4 - The RED LED on the side of the EVO-ONE will Flash rapidly.
5 - Release the push button.
6 - Press & Release the push button 5x times. Everytime the push button is pressed the parking lights
& the RED LED on the side of the EVO-ONE will blink.
7 - Then Press & Release the Brake pedal.
8 - At that same moment the RED LED on the side of the EVO-ONE will blink once to confirm that the
Telematic device ID has been learned to the EVO-ONE.
9 - Cycle the vehicle’s ignition to the OFF position to Exit the EVO-ONE programming.

2013 Impreza with eco one and rfw642 will not lunlock door when remote started.

Sun, 02 Dec 2018 05:52:22 +0000

Hello! I just installed an evo one on a 2013 Impreza. My problem is when I remote start the vehicle the rf kit will not unlock the doors. It works fine when it’s not on. I’ve checked all wires many times and they’re all connected properly. When I press the fob when the car is on, there is no blue light lighting up but it beeps and the lights flash like they normally do. The oem remote will unlock the door when it’s remote started but will not turn it off with 3xlock.

Toyota Rav4 2018 Push To start won't shut down when door is open.

Sat, 01 Dec 2018 17:37:58 +0000

I bought the Evo All with the Fortin T6 harness for my Toyota Rav4 2018 Push To start.

I updated the Evo with the newest firmware. I turned on the option "Engine Shut down when door is open". The problem is the engine DOES NOT shut down when I open the door. I step on the brake and move the out of park, the engine shut down and then automatically starts up the engine again.

Problem solved.

I stood too close to my car when I remotely started it. My car did not start so I turned off some of the options. I reloaded the suggested options. My car starts up and shuts down when I open the door.

Thank you !!...............

2013 Explorer wont complete programing

Sun, 11 Nov 2018 22:45:23 +0000

installed EVO-FORT 1/EVO RS to EVO ALL specifications found on web site, on 2013 ford explorer standard key, everything appears fine untill the final program step, when doing final flash the blue ligt blinks 10 times as it should, but instead of going off then goes to a constant yellow light? Ive cross checked wiring mulfibple times, I have verified 12amp power at the yellow wire and still nothing? any help would be greatley appricatied.

EVO One; after remote start vehicle will not shut down

Wed, 14 Mar 2018 01:25:20 +0000

I've installed two of these, within a month of each other. Both installs went smoothly. However, this last one is a 2007 Expedition.

I can start it with the fob w/3x Lock, and kill it with the 3x Lock. But it is letting me drive the vehicle without the key and will not shut off with by pushing the brake, or with the key. After the full run time, it stops like normal. I have not tried driving it for 15 minutes, as i'm afraid it will shut down while driving.

A1-A11 are active.

2013 Jeep Compass will start remotely but will not turn off and has a transmission controller fault code. What is wrong?

Mon, 01 Jan 2018 18:02:16 +0000

2013 jeep compass

I cant get through the programming on evo chrt6 2016 challenger

Thu, 21 Dec 2017 15:26:38 +0000

2016 challenger push to start , I installed the evo chrt6 and got to step 6 the red light on and it would not do anything else

I unplugged and started over and the yellow light would not flash after the 4 x button

I did a unit reset, I hope i didnt mess up anything in the settings by doing this now it is stuck with the yellow light and it wont do anything
Can you check my programming to see if it's good?

i am using factory remotes for 3x start
what do I need to do?

please help

My Dodge Journey 2013 does not start?

Thu, 16 Feb 2017 21:38:36 +0000

Hi,

I bought a EVO ALL Service # 001A06 692577 just to connect OEM remote starter, trigger lights and door signal (shut off engine) but it does not start my car.

I connected all wires as showed in electric diagram (3 times OEM remote starter) and program it under the procedure with flash link updater but when I press 3 times in the OEM remote starter, nothing happens, the trigger lights does not turn on.

I checked led lights and each time that I press lock or unlock in the OEM remote starter, light is blue in EVO module, also when I press button (dashboard) to start, light is yellow.

The problem is like the EVO module does not send signal to start engine and trigger lights or the car is not receiving it (I think so)

Could you help me to find the problem, please.

Thank you

Cesar

Focus - multiple auto cranks / no start

Sun, 08 Jan 2017 08:56:50 +0000

Hello to all.

Sorry for the long post but im trying to be as much descriptive as possible.
I would like your comments and advise in the following issue that I had when installing a remote starter on my car. Car unexpectedly died after testing the remote starter. several times.

Some background:
I have a 2015 Focus SE automatic. It barely has 3000 miles.
I purchased a Fortin EVO All bypass unit with a CrimeStopper LC1 remote starter. It comes with 2 additional remote controls and All the system came preprogrammed. I could start the car with my OEM keys (by pressing the lock button 3 times) or with the additional key fobs.

Installation process:
I went ahead and removed the bottom cover on the steering wheel and disconnected both start harnesses (main and immobilizer).
I then connected the new T-harness. 2 plugs back to the start cylinder and 2 more to the factory car harness.
I also tapped the CAN high and low and got everything ready for connecting the remote starter unit.

When plugging everything in to the EVO ALL, I had no issues. I programmed the oem keys on the Fortin unit and finished without any issues.

I tested the remote starter several times and worked perfectly with both oem keys and the extra long range remotes.

I finished up by organizing everything inside the console and routing the cables. I was very careful by not disconnecting anything.

I tested the system one more time and started to have problems. The car wouldnt remotely start.
I got inside and tried to start it normally with the key but no luck at all. The car tried to crank several times (around 3 or 4) every time i push the key to the ignition position but engine wouldn't start. It was a very rapid crank.
All lights in main console were ok so I didn't think the battery was dead. Also, no errors were shown on the dash.
Anyways, I tried to jump start the car with another car and this time, it started without issues. I left it charging for 15 minutes and disconnected the jump car. My car kept running.
When I tried to shift from P to D on the car, just by pressing the stick unlock button, car died again and wont start by its own. Only jump-starting it again would help it start but the same issue when shifting to DRIVE would happen.

I disconnected all the remote start harnesses and units and tried again. No luck

I ended up having the car towed to the dealer. I didn't do any other troubleshooting procedure.

Car Stayed at the dealer for an entire week and they finally got it up and running. They never told me specifically what happened but mentioned that a PCM fuse was "loose". Nothing else. I asked them about this fuse location and they told me that it's not accessible or on the fuse box . That doesn't make any sense.

I have been trying to find the root cause of the failure because I want to re-install the remote starter again. The thing is that I'm afraid this would happen again and have no idea on how to fix it. This installation should be very easy and the fact that it did work initially on my car makes me think that there was something else that coincidentally happened during the installation.

After all this, I would greatly appreciate your opinion on my issues. What should I do?

Thanks so much in advance.

truck does not start all the time

Fri, 06 Jan 2017 15:22:56 +0000

im using craime stopper rs4-g4 with evo ride on 2010 toyota tacoma some days it starts and some days it just turn over and the evo ride red light is on everytime when you want to remote start it but sometimes it starts or some times it just turns over

Toyota Sienna 2014 evo one with toy1 t-harness cranks but does not start

Sat, 17 Dec 2016 19:19:43 +0000

evo one with toy1 t-harness 2014 Toyota Sienna. FTX64-2W remote kit. 79.39/1.21

crank no start. Parking light Flash code 4x after not starting. Door lock was not working also and parking lights flashed 30x after each failed attempt. Door unlock was working.

2012 Focus wont unlock with RF642W

Tue, 06 Dec 2016 21:52:37 +0000

2012 Ford Focus wont unlock doors with RF642W remote (locks fine)

Connected everything according to diagram, center lock/unlock button and green/purple wire behind door kick panel.

Start and Shudwon works, lock works but wont unlock.

Evo All does not successfully program

Sun, 04 Dec 2016 20:50:23 +0000

Hi, I'm having trouble programming the Evo-All. I've checked on the FAQs and made sure I have a good connection to the ignition. Can you provide any troubleshooting why it will not program. I've managed to get to the step where I hold the program button and insert the data-link. I release when the red and the blue are illuminated and I then proceed to connect all remaining connectors. Connected the 12 pin and then the 2 adjacent 5 and 6 pin connectors. I then proceed to press the program button 2x however no change occurs. This is where I'm stuck.

Additional Info: 2012 Camry G-Key, CrimeStopper RS4-G5

Also it seems that the auto light does not turn off.

2012 cruze won't remote start with gmt1

Tue, 22 Nov 2016 16:22:17 +0000

Installed according to stand alone guide, activated stand alone using flash link 2. Module programmed o, but my car won't remote start with 3x lock. I grounded the dark blue wire on the 20 pin connector and nothing happened. When I grounded the yellow and black wire it started. No matter how slow or fast I press the lock button it won't start.

EVO-ONE: My Starter turns but my engine does not start

Thu, 10 Nov 2016 18:49:12 +0000

I have an 2011 Toyota Highlander G-Key. I've installed an EVO-ONE with T-harness Toyota 2. When I activate remote start, the engine starter turns but my engine does not start. I've checked the T-harness connection and A1 Yellow Ignition wire is spliced to the T-harness pink ignition wire. Also the yellow loop wire has been cut. Everything seems to be working like the parking lights and starter except engine won't start. please help