Evo All the car doesn't start

Hi. I installed Evo-All on the my Volkswagen Passat B7 2.0TDI 2013 year whith standard OEM key.I used the THAR-VW6 wiring harness. Firmware version 75.40. I trained the module on the car. Then the decryptor cenerated a code , all successful. But the car won't start with the OEM key fob. The relay in the module clicks , the red light comes on , then the orange light comes on , and the car radio turns on. But the engine doesn't start, and the dashboard doesn't turn on. I connect all the connectors according to the THAR-VW6 instructions. I didn't connect the wire to the brake pedal ( my car doesn't require pressing the brake to start ) I didn't connect the wires for the start / stop button, as I don't have that button. I used the lock/lock/lock combination to start the engine. Where should I connect the separate yellow wire ( yellow ignition) ?

asked Feb 13 in Volkswagen by Andrii Fomin (160 points)

1 Answer

Hello,

What is the S/N number on the back of the evo?

Thank you.

answered Feb 16 by Derek J (395,120 points)

S.N : 001A07 801355

commented Feb 16 by Andrii Fomin (160 points)

Please do the following:

- connect the evo to the flash link, click the gear icon in the right coner then click "go to pro mode"

- in pro mode turn off settings protection, then click save options

- return to the vehicle with the evo and perform a master reset: https://cdn.fortin.ca/en/download/61931/61931.pdf

- return to the pc with the evo and enable the following options, A1 through A10, C1, D1 & D2.

- then re program the evo to the vehicle including re running dcryptor

- test the system

The yellow wire from the t-harness can be connected to the yellow wire on the 20 pin connector of the evo-all.

Best regards

commented Feb 16 by Derek J (395,120 points)

I did everything as you wrote, end when the decryptor tries to generate a code for me, the following error:

Dcryptor's limit has been reached for this car . Help please...

SN: 001A07 801355

commented Feb 16 by Andrii Fomin (160 points)

I have reset the dcryptor limit.

commented Feb 16 by Derek J (395,120 points)

I reset the settings in the module and retrained it in the car, restart my flash manager , but the dcryptor returns the same error.

commented Feb 16 by Andrii Fomin (160 points)

Disconnect the evo and re connect it, it should be reset now.

commented Feb 16 by Derek J (395,120 points)

Thanks that helped, But the car won't start . I used to hear the relay in the module clicking, but now that doesn't happen. The blue light on the module only blinks three times when I press "lock lock lock " and then nothing happens. I connected the free yellow and yellow A1 wires.

commented Feb 16 by Andrii Fomin (160 points)

Verify your options.

You need A1 through A10 on as well as C1 and D1 and D2.

Best regards

commented Feb 16 by Derek J (395,120 points)

Should all these points have the value yes ?

commented Feb 16 by Andrii Fomin (160 points)

Yes.

Options A1 through A10, C1, D1 & D2 should be on.

All other options should be off.

Best regards.

commented Feb 16 by Derek J (395,120 points)

I set everything up as you said. I press the lock lock lock , then the red light comes on , then the orange light, the radio turns on, the turn signals blink twice, then everything goes out, and then the second attempt begins, and the radio turns on again, but the dashboard doesn't turn on. Firmware 75.40 , yellow A1 is connected to yellow ignition. I didn't connect the hood button. I also disabled the hood itself in the module settings.

commented Feb 17 by Andrii Fomin (160 points)

Please turn on A7 and turn off B1 and re test.

commented Feb 17 by Derek J (395,120 points)

That didn't help either. Nothing changed. At the end , the module flashes red three times. The dashboard doesn't turn on. Are there any fuses on the THAR-VW6 wire ?